Forum
Questions, builds, help and the odd argument. The mods and guides are out front.
I have AP on my E90 and they're fairly decent for the price. A bit too soft in the rear which isn't ideal if you plan to go stanceboi.
TA in E39 was annoying as fuck because of our shitty roads, so you just end up bouncing alot in the seat lol..
the suspension is old already so any replacement is better than now I think. I just want the car lower and don't want to get expensive stuff. Cutting springs is absolutely no optioon for me, I think doing that is maximum degeneracy level. But consider, 250 bux for coilovers, that's a production price about 60 bucks for a single damper with springs, for that price you have r+d, production, material, shipping from factory, and the producers want to earn something too. So you can not expect quality. Coilover install will be a lot of work too because I can't fold the seats, so I have to remove the whole rear bench for it.
no idea about welding diff prices, used diffs go for 50-100 bux here, on top of that the welding job.
bought used Vogtland 30 coilovers for a good price. Installed foglights.
Car got back from Poland, it pulls fine now, but runs too rich all the time. I don't know anymore so I'm gonna give it to a mechanic.
vanos swapped, camshaft sensor swapped again, brakes got done (minus rear discs), brake line got renewed, handbrake cable got swapped,
Got Styling 109 rims from the X3 as summer rims, need at least 30mm adapter plates for em, probably gonna get 35mm.
bought a cheap strutbar, but yes, it is actually slightly noticeable
Transmission fluid needs to be changed soon. Rear brake discs should be done aswell, got everything in my living room waiting to be installed.
Installed the multifunction steering wheel, waiting on a cable bridge to fully function.
well shit
how does this shit happen? Car is at a mechanic for a look through and compression test, the tip had its fun in the cylinder
Shit quality plugs? :/
Or either wrong plugs? Its best to always double check after getting car from mechanic. If there is hole in the piston or some shit, I can already imagine how much you gonna spend fixing it, swapping other would save a lot of cash I think as M52B20βs or M52B25βs can be bought for 180-300eur lol, time for 0.5l increase? 🙂
Yup can confirm,if it touched pistons and valves you are better off getting a new engine unless this one was really low km which I doubt
Check the engine with a camera via the spark plug hole if the cilynder is scorched get an m52b25 or a b28 for extra displacement
plugs weren't highest quality spec, my mistake.
compression is fine apparently, but idk about internals. Gonna get more info tomorrow.
spare engine for under 200 bux? lmao where? over here around 400 bux for a 2.0, 600 bux for 2.5 and 800 for 2.8
engine swap isn't a ez pz lets go job, I don't want to if I can.
if it's fine I would definitely recommend going with iridium one's next time a good set of ngk BKR7EIX are good and a step colder wich helps avoid detonation since it's rich also get single ground ones they allow larger gap and are less risky
I sold mine M52B20 for 220β¬ last winter, here in Lithuania you can get M54B30 for 650β¬.. But yeah, I know that prices for car relates things are high in Germany, shipping is not an option too cause I am sure it would cost a lot. Swap is mostly plug and play if you know what you are doing and have the place to do so, swapped broken M52B25 in E39 sedan to working M52B25 engine in less than 6 hours few months ago in driveaway, ofc we had engine lift and etc, but the most fun thing is that we got that M52B25 for 150β¬ after giving old one to the people we bought it from lol. I am sure you will figure things out soon :/
Mackay is right,I helped swapping a B25 with seatbelts instead of proper lift and worked pretty good.And yea price differences are a bitch,as I can get a B30 for 600-800e here too
