Forum
Questions, builds, help and the odd argument. The mods and guides are out front.
Hello all, my name is Marlon and I moved to Valo City one year ago after spending my previous years in the Caribbean. After a lot of saving, I finally purchased my first project car from a Japanese auction site and had it imported and landed two weeks ago. Some basic information about my car-
1995 Toyota GX100 Mark II Sedan
-Fairly low mileage, only 55,000Kms when it got here.
-Clean body, no accidents and no rust.
-16x7 wheels with new tyres.
-1G-FE engine.
-5 Speed manual, I checked the part number on the gearbox and it seems to be a W58.
The interior seems to be fair, the body is tidy and the engine is fully functional. It has all the luxuries as expected, such as functional A/C, Power steering, electronic seats, power windows and other average stuff. The best part about this vehicle is that I paid a mere equivalent of $1,200 USD, leaving lots of cash to kick off my build. It was also a non-smoker's car which means the interior is void of any odors.
My plans are to build a nice and reliable street machine that's comfortable to drive all around the country without any issues. Without further ado, here are some pictures:




Looks clean! Out of all the X100's this one is the classiest IMO. Will be following this build!
Looks so pure, clean ass GX, Gt3076r 😉
Clean and fresh. Hopefully I can see you around in my gt86
1200 is amazing, must have been a older persons car I assume.
Thanks fellas, and @Mister_Softee, the car cost $1,200USD alone. Importing, registration and other fees cost me $2,600, everything totaling to $3,800USD which isn't too bad for a project car. I haven't done much in a while due to the fact that I've been daily driving the car to and from work. However, I did pick up some stuff from the Driftworks website:
- HSD Monopro coilovers
- Driftworks front camber arms
- Japspeed rear camber arms
- Driftworks tension rods
-Some Powerflex polyurethane bushings
With these parts installed, the suspension feels much more rigid and responsive. Some pictures of my new height:


Now that I had a proper suspension setup, I looked into getting a new set of wheels on threepiece.us: Weds Kranze Cerberus II 18x9 +10 upfront, 18x9 -0 at the rear. Wrapped in 215/35/18 tyres, these wheels fit my car perfectly and give me the exact look I pictured in my head. With minor fender rolling and -3 camber all around, I achieved a head-turning sorta VIP stance.



I've decided to step back on modding the JZX100 for a bit and look into purchasing a stock daily driver so I can work on this one without having to worry anymore. With that being said, my next update should involve another car.
that looks so good on the cerberus! too bad you're on the other side of the world 🙁 would love to squad up and snap some pics of our X100's.
Haven't posted an update in ages because I've been busy with work. I did some drastic changes over the past couple of months. I ended up swapping in a JZS147 2JZGTE engine and mated it to my W58 5 speed manual transmission. It took a bit of electrical work and some late nights but we figured it out. Some other engine related mods that were done are:
-Mishimoto JZX100 intercooler kit
-Greddy Type FV BOV
-Aeromotive Fuel Pressure Regulator
-Treperformance 255lph fuel pump
-Apexi cone filter
-3" Stainless steel exhaust with v-band clamps and a shotgun tip
-HPI Oil cooler and braided lines
-Mishimoto thermostat.
-ACT 6 puck clutch and a heavy duty pressure plate
-XTD lightweight flywheel
I went to a dyno day and my horsepower figure was determined to be 305whp on stock boost and stock twins. Not bad at all. We also welded the differential and I tried out some drifting with my new alignment setup (0 toe all around, -4 camber upfront and -1 rear.) After all of these mods, my car has become a bit expensive to drive to work everyday so I'm slowly saving cash for another vehicle which would be more practical for city driving. Anyway, here are some photos:




Sick work :awesome:
So happy to see something different ! Good job !