Forum
Questions, builds, help and the odd argument. The mods and guides are out front.
a box crate engine.
Else than that, I´d plan to make a smaller engine for the car which would be something as a tinier I4 or with less cylinders.
Added 1 minute later:
....Or how about a nuclear reactor for that extra insanity!?
YES
The question is: how should I make one?
Added 19 minutes later:
http://en.wikipedia.org/wiki/Pressurized_water_reactor How about this (if anyone does not have a suggestion on how a nuclear reactor looks like)?
Added 36 minutes later:
http://en.wikipedia.org/wiki/Nuclear_propulsion#Cars
I found this (the first picture from above) but dunno which part should resemble what in this picture. Could this work?
Example (how I imagine it could work):
-block = base (for the entire structure)
-crankshaft = turbine (connected to generator)
-connecting rods = steam generator
-piston = pressurizer
-cylinder head(s) = reactor vessel
-camshafts (any equivalent part) = control rods (intake for the water part, but the exhaust is for the heated part)
-intake manifold = condenser?
-fuel = water supply/other suggestion on what?
-flywheel/clutch = still remain as usual (mounts onto the turbine to deliver the power made towards the transmission)
-transmission = still remain as usual (mounts onto the base for the structure to deliver the power made towards the wheels)
-exhaust = any equivalent part, if that is even needed?
-alternator = any equivalent part?
-drive belt (for cam/crankshaft) = any equivalent part?
-performance parts (turbos?) = any equivalent part?
-NOS/N20 = any equivalent part?/if the equivalent for intake manifold is being made
If you have ideas for how this can be improved, go ahead. This list is only a speculation on what is the best match for each part at the engine itself.
NOTE: Remember that the list is far from complete and further on ideas will be needed for this.
Well, I made some of the parts in the same way as I wrote earlier but apart from the list, the exhaust did in fact get an equivalent. As I thought around my idea now with some improvisation, the exhaust would have fitted better if it were made as a turbine assistant to make the reactor engine run smoother. A turbo application COULD POTENTIALLY WORK if installed correctly, simply by connecting the turbocharger at where the gases are cooled down and passing onto the reactor vessel.
Added 6 minutes later:
What would fit a PWR engine as it´s best, when it comes to comparison to a internal combustion engine at the specs? a four cylinder, an eight cylinder or even bigger?
Here is an animation of how the PWR works and I just want to give you a better picture of what I´m thinking of.
Having done some research in college about this very subject, I can tell you having a nuclear power plant in a vehicle (in my case a truck) requires a way to store energy. These reactors can be downsized to fit in larger vehicles but cannot vary its power output very quickly. A quick Google search reveals a reasonable value is 5-10% change in power per minute for commonly sized reactors (source). In a car (tiniest reactor possible) this would probably be a bit faster since you have much less water in the steam loop, but the main restriction is probably the turbine spool up. Also remember that you require a significant amount of cooling for the condenser.
A bank of large high voltage capacitors in parallel or lithium batteries would make sure you can take off relatively quickly and then gradually switch to almost exclusively fission power. It would be a bit like a conventional electric car only much heavier and with massive power output over time at full throttle. Massive as in enough to power a small city.
Then again this is a game so just do whatever. Maybe give it massive turbo lag?
New account bro( and dat face)?
Added 2 minutes later:
So how about a single cylinder for my cratemobile, if no nuclear power reactor as the engine itself would work?
Added 7 minutes later:
Or how if you skip the water steam part and only rely onto the warmer part as the whole "engine", that uses the control rod (at the reactor vessel) as either a throttle or "crankshaft" to get quick power?
single huge cylinder with huge blower lmao
Y U no make supah-powah-v16?
A V16 for my Box car? I have never thought of that, but also it would be nearly uncontrollable since the ass is too heavy so you would perform a lot of wheelies. I might give the "Supah-powah" name thing a try (fairly funny enough name for an engine to my box).
How about a six turbo v16 with a roots type supercharger? I always thought the V16 that came with 2.3.0 was a bit wimpy. That and the most turbos ever fitted to a slrr engine is 4 xD
Was it the higher or lower the number the better at the "fully_stripped_drag" line if I want improve the aerodynamics at the .java?
pre
Added 26 minutes later:
Got to ask this: How do I make a headlight to perform like a lantern (glowing up basicly everything around the car within a small area)?
Make the handling gokart status >🙂 (ie super low turning radius.)