VStanced/mods
Submit a mod
Mods Guides Forum Submit a mod Log in Register

Forum

Questions, builds, help and the odd argument. The mods and guides are out front.

Notifications
Clear all

[Closed] Three Star Garage

49 Posts
16 Users
0 Reactions
21.3 K Views
ParkerFM01
(@parkerfm01_14658)
Prominent Member
Joined: 12 years ago
Posts: 838
Topic starter  

24/08/2017 - Wait, what?

So uh, yeah, the Cobra now has an engine. More specifically, an LS3 (and 6speed manual transmission) out of an '09 Corvette. With the help of a BRP Hot Rods conversion kit, the engine and transmission swap was a piece of cake. I still have to finish up the wiring, but I might be good to fire it up, and maybe drive it in a few hours provided there aren't any hidden issues with the car. Doubtful, though, as I gave this car a very thorough inspection when I bought it.



   
Sleepin_mOnkey
(@sleepin_monkey_24908)
Noble Member
Joined: 10 years ago
Posts: 2440
 

WTF dude. even that i think the ford v8's got incredible potential you did a nice job on the musvette



   
Driftphantom
(@driftphantom_6153)
Honorable Member
Joined: 13 years ago
Posts: 650
 

8/29/17- Going on a diet

What's up guys, Project Circut Stang is back and she is shedding a few pounds

As you can see, we have gone through and compeletly gutted the rear of the car. Even the soundproofing material had to go! The front of the car saw some weight reduction as well as the removal of all the AC equipment. Overll, the car has lost a total of 350LBs. Not bad for a 91 boat. A 6 point roll cage was installed to increase rigidity.

Here is another picture of the interior, keep you guys posted later!



   
JdmSly
(@jdmsly_5934)
Honorable Member
Joined: 13 years ago
Posts: 693
 

Heyo, im not actually dead ive moved over to the state of Texas with the bois at Three Star Garage. I still have the s14 but i have a current project that im working on, its a 1998 Toyota MR2 with a k24a1 swap. A furious 160 Crank HP but super low compression from the factory which means boost soon. Other than that its stock besides xxrs i guess haha. Im deciding weather to sleeve the block or run stock block till it blows. Hopefully when its done i can put some work in on the fox bodys. But ill try to update this alot with the progress.



   
ParkerFM01
(@parkerfm01_14658)
Prominent Member
Joined: 12 years ago
Posts: 838
Topic starter  

29/08/2017 - We're getting there...

So, the car ran fine with the street radials and stock LS3, but i figured the car could use a little bit more...

With a little bit of magic, I found and fitted a giant Edelbrock supercharger, complete with an Edlebrock intake manifold, Demon carburetor, all that good stuff. Of course, along with some supporting mods like a new Holley fuel pump, braided lines, all that good stuff. I've some internal work to the engine, headstuds, main bearings, valve springs, etecetra... Just basic stuff for making an LS3 not explode. My butt dyno says the car's making somewhere around 750 horsepower, but I'll let the actual dyno confirm or deny that... Should be getting it dyno'd in a day or so. Another new thing is I a set of Weld S71B rear drag wheels, with some Phoenix drag slicks. I also have a set of runners for the front, but obviously they aren't installed at the moment. If you couldn't tell, the unpainted parts are now painted. Stay tuned, as some big stuff is coming soon.



   
Nexion
(@nexion_21988)
Estimable Member
Joined: 10 years ago
Posts: 182
 

8/29/17
Good Job Everyone really loving you're builds.

As for the Evan Drfit FoxBody it's slowly progressing I recently picked up some Fifteen52 Tarmac's R34's, and some and some Fifteens f40's.
17's front and rear. I Also picked up some Endless Brake pads.
There's spacers on the rear but i dont remember of the top of my head just know the pictures dont do it justice, and at the moment im trying to decide on the color for the wrap I but i think i have a idea in mind and i think you guys will Enjoy it.
Also i picked up a daily and i think you'll enjoy that as well. So Get ready for that. 😃



   
Sleepin_mOnkey
(@sleepin_monkey_24908)
Noble Member
Joined: 10 years ago
Posts: 2440
 

Holy i wish my foxbody look clean as yours guys.



   
RinKK
(@rinkk_12186)
Estimable Member
Joined: 12 years ago
Posts: 147
 

Hello, this Rinkk. DUSTER BOYSare here. I got a 71' Plymouth Duster 340 in "Sno White", or what is left of it rahter. It makes fuck-all horsepower for a 340, it has enough blow-by to kill a horse. it runs like complete shit with that Carter 4 barrell that needs a rebuild A.S.A.P. I got a Holley chilling in the shop though.

The rust is just surface so calm your tits, I got this shit for 1500V$, it sat in a garage for at least 20 years, in fact, it's last registration was July of 1988. The engine isn't original, it's a original 340 duster but the engine's been swapped sometime in the 70's, considering the odo has "1243" miles, I'm guessing it turned over at least once, if not more, so this thing got driven. From what the owner told me, the car was his grandpa's and he died in 1990, so I'm guessing he just left it in the yard. Luckly it's Texas, and the car was in the desert, so it's not actually rusted.



That hot 340 and it's oil leaks.

And that THICC ass

Four on the floor, interior is clean as hell, just needed a clean-up.

First things I'ma do, is a 200 shot and a fatter carb.



   
JF1
 JF1
(@jf1_12736)
Noble Member
Joined: 12 years ago
Posts: 1166
 

Sleeper?



   
JdmSly
(@jdmsly_5934)
Honorable Member
Joined: 13 years ago
Posts: 693
 

nigga shits ugly

eggs dee jk


   
ParkerFM01
(@parkerfm01_14658)
Prominent Member
Joined: 12 years ago
Posts: 838
Topic starter  

@Rinkk: Who the fuck are you?--If your shit turns out to be fire, you can stay.
@JdmSly: Welcome!

30/08/2017 - Should have done this a while ago...

Well, since the Cobra clearly isn't getting plates anytime soon, I picked up this 2012 Nissan 370Z Touring as a daily driver. It doesn't have anything done to it apart from the BC Racing BR Coilovers and 19" AVS Model F7 wheels. Though, being my daily driver I may raise it up slightly, and opt for a smaller wheel and thicker tire combination. I dunno, we'll see what happens. Apart from that, I don't have much to say. Expect some more from the 370Z and Cobra soon...



   
JF1
 JF1
(@jf1_12736)
Noble Member
Joined: 12 years ago
Posts: 1166
 

Looks nice.



   
ParkerFM01
(@parkerfm01_14658)
Prominent Member
Joined: 12 years ago
Posts: 838
Topic starter  

@Jfernando1: Thanks!

31/08/2017 - It's time

Yesterday, we dyno'd the car... It makes 827 wheel horsepower. I'm speechless, this car is fucking insane. This morning we finished up the rollcage, racing seats, harnesses, fuel cell, disabling the air bags, all that good stuff. Now it's time to make the first pass at the drag strip.

Creeping the car up to the tree was nerve-wracking; 'This is it', I thought to myself. Well, it wasn't quite 'it', since I missed second and ended up with a quarter mile time of 11.110. That's still quick, but the Cobra can go faster. I know it can. Unfortunately that was all I had time for that day, as I needed to be home by 3:30 to sign for a package. I promise I didn't order anything for the 370Z already. 😉



   
JdmSly
(@jdmsly_5934)
Honorable Member
Joined: 13 years ago
Posts: 693
 

You know i had to pull up on this hoe when she popped up on the local face book group. An amazing 1991 Nissan 240sx with an original 313,402 miles on the chassis its salvage title but who cares its a 240 am i rite? I checked the car fax its had 8 Owners and been to more states than i have been, and to include its been stolen once. It has a box C title meaning that the mileage on the cluster isnt real so who actually knows what this car has had done to it. All i know is that its got full interior thanks to the last owner, along with the front end its been fixed and straightened out. Fake watanabes, bald tires, a ka24de that has the block from a nissan frontier and the head from a s14 with some nice oil burning properties. Over all this thing is the cleanest turd 240 ive ever seen i mean its mostly one color and lets not forget its welded diff and its constant gear grind in 3rd. But over all of that it drives straight so i cant argue, im just happy to start drifting again!



   
MrTomush
(@mrtomush_26354)
Member
Joined: 10 years ago
Posts: 330
 

Nice S13, shame you have change gearbox, because your gearbox is gone



   
Page 2 / 4
Share: